Peach tree pruning in summer can assist plastic surgery, inhibit shooter growth, reduce nutrient consumption, improve ventilation and light transmission within the crown, promote flower bud differentiation, improve fruit quality and increase yield. Summer cuts are usually 3-5 times in summer, mainly in May-August.
After budding peach trees germinate, it can be carried out to remove dense buds, back buds and improperly positioned buds. When the new shoot grows to 5-6 cm, it wipes away the useless shoots. The double tip leaves a large angle and erases the small angle. Sprouts within 15 centimeters of the base of the branches and the clumps of sawn cuts should also be erased promptly.
The topping of the peach tree itself has a large amount of occurrence, and the topping can easily cause excessive shoots and canopy closures. Therefore, in addition to sapling shaping, the peach tree cultivation requires the topping of the main and lateral branch extension branches. The summer shearing of the peach tree is generally not recommended. Tip topping.
Twist tip When standing upright 25-30 cm long, half lignified, hold the base of the new shoot 5-10 centimeters to reverse 180 degrees, making it oblique or sagging. Twisting tips are usually carried out in May-June. If the twisted spots appear again and again, the twisting tip can be performed again. In addition to being selected to extend the shoot and its auxiliary shoots, the competing branches of the other branches, the back branches of the backbone branches, the forever branches of the inner branches, and the long branches that are drawn near the large wounds can be twisted. Tip. Twisting shoots can control long shoot lengths, ease tree vigor, and transform them into full-fledged branches, with the dual effects of results and renewal.
When the shoots are up to 30 centimeters long, they can judge the quality and nature of the shoots according to their growth potential, thickness, and location, and select strong and strong branches to stay in place, and sparse the competition branches, leggy branches and thin branches. Dense branches, upright branches, and drooping branches. After the fruit is harvested, remove some dense branches of perennial branches, branches of the year, some branches on the back or on the outside. After cutting and flowering, the fruit branch that has set fruit can be left with a short shoot at the upper part of the young fruit, and the middle and long fruit branch that has left the flower but not set fruit can leave 2-4 buds short, so that it can get the result of the year. Before June, if there is space in the leggy branches that sprout on the branches of the main and lateral branches and within the crown of the tree, 1-2 nodes in the base may be ultra-shorted to produce small and medium-sized branches; if there is no space, Base sparse.
The branches are also known as litchi. They change the growth direction of the new 60 cm-long shoots with lateral characteristics by taking branches. They use four fingers to hold the new shoots, and the thumb presses down on the top, while the four fingers move up and down at the same time. The top, moving from the base of the new shoot gradually to the tip, hurts the xylem, and hears the sound but does not fold it. Taking branches can ease the branching tendency, which is conducive to the accumulation of nutrients and flowering results. It is generally conducted in July-August.
Pulling branches and pulling branches are the key measures to ease tree vigor, sapling shaping, early results, and prevention of baldness in the lower part of the branches. The main and lateral branches or the relatively large vertical branch groups with small opening angles and unsuitable extension directions are used. , Can be used to support, pull, do not, fall and other methods to open the angle or adjust the position. The branching angle is generally around 80, and can not be pulled into a horizontal or sagging state; for the main and lateral branches with too large opening angles, the branches with branching branches can be used up to narrow the angle, which is more than August.
Access Control Keypad is a security product that can be connected to a lock and unlocked by swiping card, password, fingerprint, mobile phone, etc. Residents can connect the access control keypad to the electric lock, Magnetic lock, etc., and then control the door opening by access control keypad.
The access control keypad also plays a very important role in the whole intercom system. If there are multiple doors in the building and residents need to be controlled to open all doors. For this project only needs to use one main video intercom system in the main door. For example, there are two doors in the building.
We can offer you with two solution for this project:
1. Customers can use 2 sets Video Door Phone for two doors
2. Customers can use 1 set video door phone and 1 set access control keypad,one for mainly door and another one for side door or basement.
Usually many customers will choose to use the second one solution. Because it can save more money for the whole project to the greatest extent.
There are many different solutions for the connected access control keypad, which can be modern access control keypad, open the door with a password or swipe card, and some customers like to be more intelligent, that is remotely unlock, which can work together with the video door phone to remotely unlock two doors through the mobile phone APP.
The following is our access control keypad, which supports password and card swiping.
The following are its parameters for your reference:
1. metal shell, waterproof
2. Touch the button
3. 1000\4000 users
4. anti-flapping door
5.external card reader
We are a factory specializing in the production, manufacture and research and development of Access Control System for 11 years. If you want to know more about us, please send us an inquiry, we are very honored to share the catalogue and price with you.
FAQ
Q: What is your service ?
a. we can offer OEM&ODM services
b. All software free provide , and technical support after-service
c. Online installation guide services.
Q: Whats the MOQ?
To ensure the best logistic cost, we suggest 100pcs(one carton).However, we are open to take orders with small qty.Welcome to sample order, contact with us.
Q: What payment terms are available?
T/T, Paypal, Western Union, credit card.
Q: How long is your production lead time?
Sample Order-Within 1-5 working days.
Bulk Order - 15-20 days for neutral items, 7 days if the items we have stock
Q: What's Your Products Warranty?
We Offer 12 Months Warranty after shipment sent.
Access Control Keypad,Gate Entry Keypad,Keypad Access Control System,Door Entry System Keypad
Zhuhai Mingke Electronics Technology Co., Ltd , https://www.zhmkdz-electronics.com