First, feeding and management 1. Enclosure environment: clean, dry, dust-free, temperature is suitable for 18-25 degrees Celsius, moderate density (3 heads/M2), good ventilation (no thirsty wind), adequate lighting. 2. Tuning: Piglets should be strengthened in feeding and management within a week of purchase, so that pigs can develop good habits of eating, sleeping, and excreting, which will facilitate future management and reduce labor. 3. Feeding: 30 pounds of body weight or less, can be fed 5 times a day, the time interval should be the same for each feeding, can be fed suckling pig or use SL221 ingredients. 30 pounds -60 pounds of body weight are fed four times a day, using S512 ingredients. 60 pounds - slaughtered, feed 2-3 times a day, using S513 ingredients. The daily feed intake is calculated as: Weight less than 30 pounds = Weight = 0.05 pounds. 30-100 pounds = weight * 0.045 pounds. 100-160 kg = weight * 0.04. 160 - slaughter = weight * 0.035. Based on the above formula, the calculated daily feed intake can be reduced in summer and autumn, and it can be increased in winter and spring. (except for free intake) 4. Drinking water: The daily water intake of a pig is about 2 times the daily intake, and it can be increased in an appropriate amount during the hot season. Therefore, sufficient and clean drinking water must be given. 5. Castration: The piglet castration can be implemented during the second week of the purchase and when it is fasted in the morning, it must be done when the piglet is in a good state of mind, healthy and disease-free. Before filling, add water to the water or feed. 800 kg of water or 400 kg of spices are used together for 7-15 days to reduce the pig's stress. 6. Disinfection: A, environmental disinfection, disinfection usually 1-2 times a week in the summer, 3-4 times a week in winter, disinfection once a day in the disease-prone season (with pig disinfection) can choose to use Wei Kang, special kill or farm blessing Use in turn to avoid virus and bacterial resistance. B, disinfection of drinking water, every three days plus three days Wei Kang or potassium permanganate, can also be used Xin Kang Kang or Keduening (200-400 kg per bag of water) Second, disease prevention and control 1. Piglets were immediately injected with swine fever vaccine when they were purchased. Each piglet was injected with 6-8 piglets and 1-3 ml of Delixian was injected at the same time. Other vaccines can be used to develop a reasonable immunization schedule according to the season and local disease epidemic. All kinds of bacterins do not do as little or as little as possible, through careful management, regular administration of drugs to prevent bacterial diseases; strengthen disinfection. Piglets allergic to the vaccine can be treated with 2 ml of epinephrine or dexamethasone. 2. After 2 hours of water supply to the piglets, the piglets should be given less ground, avoiding stress diarrhea, accelerating the water intake in the water, and even drinking for a week, drinking better in the long term. Can improve the disease resistance of pigs. Promote growth and development of piglets. After four hours of purchase, feed (appropriate amount of material in the first three days before purchase, and feed six or seven full meals per day). Adding Hushushu or Hunuoyu (100g per 100 kg of feed plus feed) for a week, Control common bacterial diseases. 3. When the piglets purchase the second week of deworming, they can add Dinobi (50g per 100 pounds of feed) into the feed and feed it for a week to remove various parasites inside and outside the pig. When it is purchased two months later, the pig will no longer be disturbed by parasites when it is slaughtered. 4. When the piglet is purchased for the second month, another week of Hunobi is added to the feed. Before the weight of 80 and 130 pounds, the feed is supplemented with Taishuping (80g per 100 pounds of feed) or oxytetracycline for one week. Salt (mixed 200 kg of feed in each bag) controls various respiratory diseases. (Liaoning company Qiu Baoku)
This classification mainly includes the aluminum die casting Machinery Parts using in Bulldozer Components area.
From the part, we can easily find that the parts have a lot of features of big cavities, so the part will have big potential risk of mold release problem, if so, the part may happen to be deform, sticking to the mold etc, especially when the part sticking to the mold, if no clear in time, while next shot, the mold may be destroyed while clamping.
Product Dimensions: Customized
Die Casting Bulldozer Parts,Die Casting Bulldozer Components,Al Die Casting Bulldozer Components
NINGBO ZHENHAI BOLANG METAL PRODUCTS FACTORY , https://www.casting-part.com