The ampoule filling and sealing machine is hereinafter referred to as the potting machine. It is a step-type transmission system, a balcony structure, multiple potting, stepless speed regulation, and can be used with the tunnel dryer and ultrasonic cleaning machine, or can be used in a single machine.
1 Working conditions The gas pressure of the potting machine should not be lower than 25kpa.
2Material requirements The parts in the potting machine that come into contact with the liquid must be made of ultra-low carbon austenitic stainless steel with corrosion resistance and stable performance.
3 structural requirements 3.1 The average wind speed of the potting machine operating area should not be less than 0.35m / s.
3.2 The potting machine should be equipped with a bottle-free irrigation mechanism.
3.3 The potting machine should be easy to adjust the ampoule specifications.
3.4 Potting machine In normal work, each movement mechanism should be coordinated, reliable, and free of stuck.
4 Loading error The filling capacity of the potting machine should be stable, and the loading error should be in accordance with the provisions of Appendix IB Injection Volume in the Pharmacopoeia of the People's Republic of China (2000 Edition).
5 seal pass rate potting machine after sealing and sealing the qualified ampule tip should be round and smooth, no hoe, pointed, hoe, focus, no leakage. Sealing pass rate should be no less than 98%.
6 The noise value of the potting machine during the idle operation should be no more than 80dB (A).
7 potting machine should have the following protection functions:
7.1 The bottle at the entrance shall be piled up, and the oven conveyor belt shall stop automatically.
7.2 The bottle at the entrance is missing, and the bottle feeding mechanism should be suspended.
7.3 There is a safety device when entering the bottle, and it can automatically stop when the bottle is bottled.
7.4 When the bottle screw is missing, the bottle is automatically stopped when filling.
When the 7.5 laminar flow fan is not started, the host does not start.
8Electrical safety performance requirements 9 Appearance 9.1 The outer surface of the potting machine shall not have obvious scratches and unevenness.
9.2 There shall be no cracks, craters, welds and incomplete penetration at the weld.
10. Test Method 10.1 The gas pressure of the potting machine was measured using a pressure gauge.
10.2 The stainless steel material used for parts and transmission parts in contact with the liquid medicine in the potting machine shall have a material quality certificate.
10.3 The average wind speed in the operating area of ​​the potting machine shall be tested in accordance with the test method of 3.3 of JGIT19-1999.
10.4 Eye force detection No bottle of liquid filling head should be leaked without medicine, no bottle is not filled.
10.5 Visual inspection The potting machine can be used to interchange the specifications.
10.6 Verify the coordination and reliability of the moving parts of the potting machine by manual and visual inspection.
10.7 Loading error test
1 Working conditions The gas pressure of the potting machine should not be lower than 25kpa.
2Material requirements The parts in the potting machine that come into contact with the liquid must be made of ultra-low carbon austenitic stainless steel with corrosion resistance and stable performance.
3 structural requirements 3.1 The average wind speed of the potting machine operating area should not be less than 0.35m / s.
3.2 The potting machine should be equipped with a bottle-free irrigation mechanism.
3.3 The potting machine should be easy to adjust the ampoule specifications.
3.4 Potting machine In normal work, each movement mechanism should be coordinated, reliable, and free of stuck.
4 Loading error The filling capacity of the potting machine should be stable, and the loading error should be in accordance with the provisions of Appendix IB Injection Volume in the Pharmacopoeia of the People's Republic of China (2000 Edition).
5 seal pass rate potting machine after sealing and sealing the qualified ampule tip should be round and smooth, no hoe, pointed, hoe, focus, no leakage. Sealing pass rate should be no less than 98%.
6 The noise value of the potting machine during the idle operation should be no more than 80dB (A).
7 potting machine should have the following protection functions:
7.1 The bottle at the entrance shall be piled up, and the oven conveyor belt shall stop automatically.
7.2 The bottle at the entrance is missing, and the bottle feeding mechanism should be suspended.
7.3 There is a safety device when entering the bottle, and it can automatically stop when the bottle is bottled.
7.4 When the bottle screw is missing, the bottle is automatically stopped when filling.
When the 7.5 laminar flow fan is not started, the host does not start.
8Electrical safety performance requirements 9 Appearance 9.1 The outer surface of the potting machine shall not have obvious scratches and unevenness.
9.2 There shall be no cracks, craters, welds and incomplete penetration at the weld.
10. Test Method 10.1 The gas pressure of the potting machine was measured using a pressure gauge.
10.2 The stainless steel material used for parts and transmission parts in contact with the liquid medicine in the potting machine shall have a material quality certificate.
10.3 The average wind speed in the operating area of ​​the potting machine shall be tested in accordance with the test method of 3.3 of JGIT19-1999.
10.4 Eye force detection No bottle of liquid filling head should be leaked without medicine, no bottle is not filled.
10.5 Visual inspection The potting machine can be used to interchange the specifications.
10.6 Verify the coordination and reliability of the moving parts of the potting machine by manual and visual inspection.
10.7 Loading error test
Baby Squid
ZHEJIANG EVERNEW SEAFOOD CO.,LTD , https://www.evernewseafood.com